Forged Wheel
XYZ Forged HH-05
SKU: XYZ-WHL-HH-05
Understanding wheel fitment
Diameter × width
Diameter is the measurement across the face of the wheel in inches. Width is the distance between the inner and outer bead seats. Wider wheels need wider tyres and may require fender rolling or spacers.
PCD (bolt pattern)
PCD (Pitch Circle Diameter) is the number of bolts × bolt-circle diameter in mm. Example: 5×114.3 means 5 bolts on a 114.3mm circle. This MUST match your hub exactly — no adaptors are supplied.
Offset (ET)
Offset (ET) is how far the mounting face sits from the centre line, in mm. Higher (positive) numbers tuck the wheel in; lower (or negative) numbers push it out. A wheel that is 1–3mm off stock offset can still fit; more than that and you will need arch work.
Centre bore
Centre bore is the diameter of the central hole in millimetres. It must equal or exceed your hub bore. Smaller = will not fit. Larger = use hub-centric rings (included free on request).
Load rating
Load rating is the maximum kg each wheel is rated to carry. Confirm your vehicle axle weight (GVW ÷ 2) is below this figure. All XYZ Racing forged wheels exceed OEM factory ratings.
Not sure this fitment clears your setup? Share wheel/tyre/suspension specs with [email protected] and we'll confirm.
Tell us your car (top of the page) and we'll set the recommended bolt pattern, bore and offset for your car — at no extra cost. Please check the figures against your vehicle before you order.
Added to basket ✓
About this design
Complex geometric mesh face with angular triangular windows cut across the spoke lattice, sitting concavely behind a stepped outer barrel ringed with assembly bolts. The engineering-part quality of the face is raw and technical — this is not a wheel that hides what it is. One for a clean wide-arch build that wants serious paddock-grade visual complexity.
HH Series
Old-school deep dish, rivets out
Some shapes you honour rather than modernise. The HH is unapologetic old-school deep dish: a dramatically concave face set well back behind a wide, stepped lip ringed with exposed barrel rivets — the clearest possible statement of genuine multi-piece construction. The dish depth is pronounced and consistent across the series whatever the spoke design, so the stance is built in. Faces range from broad six-spokes to dense twin-spoke and curved fan layouts, all sitting on the same deep, riveted barrel. It's for the build where the engineering is meant to be on show, not tucked away.
Forged to order — built for one car: yours
Every XYZ forged wheel is made to order. Beyond the offset (ET), width (J) and bolt pattern, you can commission a completely bespoke design and colour — down to a single wheel if that's all you need. This is genuine one-off manufacturing, not a fixed catalogue.
Engineered, then tested to destruction
Once your order is placed, the design is run through stress-analysis software to verify its structural safety factor. Then we prove it physically: for every customer's vehicle we build additional wheels and fit a brand-new tyre purely for destructive mechanical testing to VIA / JWL and TÜV standards —
- Dynamic Radial Fatigue Test
- Dynamic Cornering Fatigue Test
- Impact Test
A wheel is only released once it has passed both the computer analysis and the physical destructive testing and met every applicable safety standard. Completing the programme takes six wheels per vehicle — it costs more than mass-produced wheels, and that is exactly the point. Three official VIA / JWL test reports are included in the box.
Made for people who love their cars
If you want something genuinely one-of-a-kind — a bespoke design, a unique colour, or a forged wheel inspired by the supercars you grew up with, built to fit your car — this is where you start. We are one of very few manufacturers in the world that will take a single-piece, fully custom wheel design and put it through the full safety programme above. And if your car runs air suspension and tucks deep into the arches when parked, these wheels were made for that stance.
Good to know before you order
- Custom width (J) and offset (ET): no extra charge.
- Bespoke designs welcome (priced on the design). 3D curved-surface and left/right directional designs carry a small per-wheel charge.
- Over 20,000 PPG / Axalta colours, two-tone finishes and custom centre-cap logos supported.
- VIA / JWL certification is included free on every current design.
- Minimum order is two wheels of the same size and colour.
- Website images are a guide only — every wheel is built from a final 2D drawing that you approve and sign.
Options & hardware
